Studsvik Cladding Integrity Project (SCIP)
Ongoing
Joint project

Left: Scheme of Studsvik LOCA test facility Right: Microstructure of fragmented nuclear fuel, Studsvik

The Studsvik Cladding Integrity (SCIP) project investigates nuclear fuel behaviour and cladding failure that may arise during operation and Loss of Coolant Accident (LOCA) transients. More recently, investigations of fuel behaviour in storage after operation have been added to the project scope (in the fourth phase).

For the SCIP project, Studsvik Nuclear AB (Sweden) conducts advanced out-of-pile experiments on irradiated nuclear fuels and claddings in its laboratories. Most of the test rigs have been customised to simulate for example nuclear fuel accidents and storage conditions which, together with advanced microscopy and other characterisation technologies, provide the participating organisations from industry, regulation and research with important reference data for modelling fuel and clad behaviour.

Over the years, the SCIP project has fostered international co-operation and continues to establish a common understanding on key nuclear fuel safety issues between regulatory bodies, utilities, vendors and research organisations with an increasing membership.

SCIP phases

First phase (2004-2009)

In the first phase, detailed investigations of how cladding properties affect fuel rod failures that may arise during operation were performed. Irradiated PWR and BWR claddings ramp testing of 11 fuel rodlets, comprehensive non-destructive examination and destructive examinations, mechanical testing and extensive micro-structural characterisation were completed. Regarding pellet-clad interaction, a modified mandrel testing technique to study iodine induced stress corrosion cracking (ISCC) was developed and mechanical test techniques were enhanced to better simulate in-reactor behaviour. The project provided an enhanced understanding of the dominant failure mechanisms for LWR cladding during normal operation and anticipated transients focusing on high burn-up cladding (Studsvik Cladding Integrity Project (SCIP): Executive Summary).

At the end of the first SCIP phase, it was clear that fuel damage studies remained of high interest for reactor performance and safety. At the same time many fuel manufacturers were developing new advanced pellets, aiming to reduce the failure risk, which contributed to the high interest in these questions and a new SCIP phase on fuel failure mechanisms could be successfully launched with an increased number of members.

Data and reports from SCIP phase one may be obtained upon request at https://www.oecd-nea.org/tools/abstract/detail/csni2019.

Second phase (2009-2014)

A second phase (SCIP-2) of the project started in July 2009 and was completed in June 2014. It was built on the considerable knowledge generated in the previous SCIP programme phase. The goal of the second phase was to continue generating high quality experimental data to improve the understanding of the dominant failure mechanisms for water reactor fuels and to devise means for reducing fuel failures. The major focus had been on cladding failures that are caused by pellet-cladding mechanical interaction, especially stress corrosion and hydrogen-assisted fracture mechanisms, as well as on the propagation of cladding cracks.

In parallel with SCIP phase 2, Studsvik, on behalf of the U.S. Nuclear Regulatory Commission, carried out a LOCA test series and shared the results with SCIP members. The NRC LOCA test programme at Studsvik had the objective of investigating the strength and ductility of High Burn-up (HBU) rods after ballooning, rupture, oxidation and quench. The fine fuel fragmentation and dispersal observed in the first four Studsvik tests was unexpected (M. Flanagan, P. Askeljung and A. Puranen, “Post-Test Examination Results from Integral, High-Burnup, Fuelled LOCA Tests at Studsvik Nuclear Laboratory”, NUREG-2160, August 2013, Report on Fuel Fragmentation, Relocation and Dispersal (FFRD)) and it brought the subject to the fore when a new phase of the project was under discussion and the focus of the project moved to LOCA.

The scope and objectives of the phase 3 of the project were established following extensive discussions within the SCIP community, including a dedicated workshop in June 2013.

Third phase (2014-2019)

Based on the outcome of the 2013 workshop and the needs and interests of the SCIP community, the third phase (SCIP-3) of the project was devoted to:

  • Determine and quantify parameters affecting fuel fragmentation and dispersal in loss-of-coolant accident (LOCA) – The mechanism behind the fine fragmentation and fuel dispersal observed in LOCA tests with very high burn-up fuel were studied to determine and quantify the parametric thresholds of fuel fragmentation and dispersal. The investigation included the effects of parameters, such as fuel burn-up and microstructure, cladding strain, temperature, internal gas pressure and gas flow at the time of rupture and the importance of transient fission gas release.
  • Analyse the consequences of off-normal temperature transients – Transients leading to cladding overheating even without large cladding strain or failure still affects cladding material properties. Depending on the severity of the transient fuel, it may be affected to an extent that might challenge continued operation or normal waste handling, transport and storage. The objective of this part was to define criteria and assess overheated fuel rods for classifying them as undamaged or damaged. Damaged fuel rods would require non-standard handling, transport and storage procedures which might have a large economic impact.
  • Observe effects of axial load on cladding failure – Large axial dimensional changes are induced in fuel rods by the temperature occurring during a LOCA. Restricting axial contraction during quenching, e.g. by mechanical interaction with spacer grids, might impact the extent of cladding damage and fragmentation. The objective here was to determine the impact of axial load on cladding performance under LOCA conditions.
  • Study the effect of power ramp rates on PCI failure risk – SCIP-3 studied the mitigating effect of low ramp rates on PCI fuel failure risk and created the basis for eliminating unnecessary conservatism during plant operation.
  • Support model development and verification – SCIP-3 contributed to the mechanistic understanding of fuel fragmentation and dispersal phenomena and thus supported model development. Modelling was also used to support the set-up of experimental parameters. Modelling workshops were an integral part of the SCIP-3 programme.
  • Knowledge transfer: Knowledge transfer was integrated into the programme, using renowned experts. Expert contributions were an integral part of the workshops and programme review group meetings.

There was also a smaller part of the project related to pellet cladding interaction (PCI) failures. Modelling was also an essential and integral part of the project.

Report on Fuel Fragmentation, Relocation and Dispersal (FFRD)

Pellet-Clad Interaction (PCI) in Water-Cooled Reactors Workshop on pellet-clad interactions (PCI) in water-cooled reactors.

Fourth phase (2019-2024)

The fourth phase, SCIP-4, which is in progress since 2019, aims to extend the experimental and modeling work related to Pellet Clad Interaction (PCI) and to LOCA issues and to investigate fuel and cladding performance related to interim storage. For PCI, microstructural characterisations and modeling activities are conducted. For LOCA, investigations of fission gas release in transients and of fuel fragmentation, relocation and dispersal, including microstructural characterisations of fuel fragmentation are performed. Spent fuel pool LOCA studies are also conducted. For back-end studies, creep and hydride reorientation phenomena are investigated. Spent fuel rod transport and handling accident studies are also conducted.  

SCIP-4 intends to:

  • generate high-quality experimental data to improve the understanding of the dominant failure mechanisms for water reactor fuels and devise means for reducing fuel failures,
  • achieve results of general applicability (i.e. not restricted to a particular fuel design, fabrication specification or operating condition)
  • achieve experimental efficiency through the judicious use of a combination of experimental and theoretical techniques and approaches.

Related external links

https://www.studsvik.com/scip-project/what-is-scip/

Flanagan, P. Askeljung and A. Puranen, “Post-Test Examination Results from Integral, High-Burnup, Fuelled LOCA Tests at Studsvik Nuclear Laboratory”, NUREG-2160, August 2013

Participants

SCIP: Czechia, Finland, France, Germany, Japan, Korea, Spain, Sweden, Switzerland, United Kingdom and United States

SCIP-2: Czechia, Finland, France, Germany, Japan, Korea, Norway, Russian Federation, Spain, Sweden, Switzerland, United Kingdom and United States

SCIP-3: China, Czechia, Finland, France, Germany, Hungary, Japan, Korea, Norway, Russian Federation, Spain, Sweden, Switzerland, Ukraine and United States

SCIP-4: China, Czechia, Finland, France, Germany, Hungary, Japan, Korea, Russian Federation, Spain, Sweden, Switzerland, United Kingdom, Ukraine and United States

Project period

SCIP: July 2004 to June 2009

SCIP-2: July 2009 to June 2014

SCIP-3: July 2014 to June 2019

SCIP-4: July 2019 to June 2024

Budget
SCIP: SEK 60 000 000 (~5.7 M€)
SCIP-2: SEK 76 200 000 (~7.2 M€)
SCIP-3: SEK 120 000 000 (~11.35 M€)
SCIP-4: SEK 144 790 000 (~13.7 M€)